AstroAI ASIKFCWR Wide Neck Plastic Foam Cannon
INTRODUCTION – AstroAI
Thank you for purchasing the AstroAI Heavy-Duty Portable Air Compressor. – The product features an automatic overheating protection system. Once the product reaches an unsafe temperature, it will automatically shut off to protect its circuitry.
It also has 4 anti-slip rubber pads to make the product more stable. Thank you again for choosing AstroAI, if you have any questions or concerns regarding your product, please get in touch with us at support@astroai.com
WARNING
- Please pay attention to electrical safety when using the product.
- Please do not use the product for unintended purposes.
- Keep the air compressor away from heat sources, such as a car’s exhaust pipe. Do not use the air compressor around flammable liquids or gases. Keep the air compressor away from fire, corrosive liquids, and strong magnetic fields.
- Check the exterior of the air compressor before use to ensure it is intact. Do not use it if any parts are damaged.
- Do not disassemble or repair the compressor. Professional technicians should perform any repairs.
- Risk of electric shock, do not use the air compressor if it is damaged or if wires are exposed.
- Do not overinflate tires. High-pressure air can cause injury.
- This product is compatible with vehicles, cars, bicycles, motorcycles, SUVs, and more. It is also appropriate for RVs, ATVs, ORVs, and pickup trucks.
- The product provides fast inflation in bicycle tires, but without proper monitoring, this rapid inflation could cause blown tires. Please promptly stop the inflation when the pressure reaches the manufacturer-recommended value.
- The product uses accessories rated at 150 PSI. Abide by the inflation instruction provided by the tire manufacturer, which can be found on the tire sidewall. Please get in touch with the manufacturer if you are confused.
- Use the product in a dry environment. Do not store the air compressor in high-temperature or humid environments.
- Disconnect the air compressor from all power sources when not in use.
- The exposed components may get hot during operation, please wear protective gloves to handle the product.
- Do not move the air compressor by pulling the air hose or power cord.
- PSI, Bar, kPa, and kg/cm’ are pressure units, not the pressure levels.
- If pressure is below 40 PSI, the compressor’s maximum working time is 45 minutes. Allow the product to rest for at least 20 minutes after 45 minutes of continuous use.
- During continuous use, the air compressor may get hot. Let it cool down before storage.
- Connect the product to a (DC 12 V) 45 A vehicle battery.
- Do not use chemical substances to clean the air compressor. Only use mild soap and a cloth dipped in hot water to clean the plastic parts.
- Do not let the product work alone without any supervision.
- If accessories are missing or damaged when you receive the package, please contact us.
PACKAGE INCLUDES
- Foam Cannon × 1
- User Manual × 1
- Warranty Card × 1
SPECIFICATIONS
- Capacity: 1L
- Applicable Pressure Range: 1000-3000 PSI
- Material: Brass, Nylon, PE
PRODUCT COMPONENTS
PRODUCT SIZE
DIAGRAM
- Metal Heat Sink
- Handle
- ¼ • NPT Quick Connector
- Reset Button
- Power Button
- Power Cord
- LCD Screen
- LCD Backlight Button
- LCD Button
- Deflate Valve
- Quick Connector
- Airflow Valve
- ¼ • N P T Quick Connector
- Rubber Air Hose
- 2xAir Nozzle Cones
- Needle Valve Adapter
PREPARATION
- When operating the air compressor, please ensure it is set up in a safe location.
- Place the air compressor on a dry, even surface.
- Unpack the package to check if there is any damage. Untie the power cord at full length.
- How to connect the¼” NPT quick connector to the air hose:
- Pull down the snap ring backward.
- CD Connect the¼” NPT quick connector with the snap ring and secure them together.
- Release the snap ring to secure the connection.
INSTRUCTION – AstroAI ASIKFCWR Wide Neck Plastic Foam Cannon
Note: Ensure the airflow controller has sufficient power before – using the air compressor.
- Securely connect the air hose to the¼” NPT quick connector of the air compressor, and connect the other end of the air hose to the¼” NPT quick connector of the airflow controller.
- Remove the valve stem cap from the tire stem, then connect the airflow controller” ‘s quick connector to the valve stem.
- Press the LCD Button to turn on the screen. Press it again to choose the desired unit. 4 options: PSI, Bar, kPa, kg/cm’.
(Note: The screen will auto shut off after 1 minute of no operation.) - Start the engine, open the hood, then connect the red clamp to the positive terminal of the vehicle’s 12 V battery, and connect the black clamp to the negative terminal.
- Pull the airflow valve downwards and switch the Power Button of the air compressor to the “I” side to start the air compressor.
- Push the airflow valve upwards to stop the air inflow into the pressure gauge. Doing this reduces airflow pressure errors and helps accurately measure the interior pressure value. After getting the pressure value, pull the airflow valve downwards to continue inflating (if needed).
(Note: The air compressor continues inflating even if the airflow is blocked.) - When the pressure reaches the manufacturer-recommended level, press the Power Button on the “O” side and remove the air hose from the tire stem.
(Note: Excessive inflation leads to high pressure inside the tires. Press the Deflate Valve to deflate the tire, and release the button to stop deflation.)
TROUBLESHOOTING – AstroAI ASIKFCWR Wide Neck Plastic Foam Cannon
The air compressor will not inflate
- Ensure the air hose’s¼” NPT quick connector is securely connected to the air compressor.
- Ensure the airflow controller’s ¼” NPT quick connector is securely connected to the air compressor.
- Ensure the battery clamps are correctly connected to the battery.
- The air compressor triggers the overheating protection system, please cool it down for 20 minutes.
- The high current may activate the current protection system; the maximum current of the product is 45 A.
An air compressor is working abnormally
- The connection between the air nozzle and the tire valve is not secure.
- Insufficient battery level of the airflow controller, please promptly replace the battery.
- The Reset Button has not been pressed correctly.
Slow inflation
- The connection between the air nozzle and the tire valve is not secure.
- Excessive use will slow the compressor’s inflation rate. Unplug the compressor and let it cool for at least 20 minutes.
- The airflow controller’s battery level is insufficient, replace the old batteries.
Air leakage
- The connection between the air nozzle and the tire valve is not secure.
- Ensure the air compressor”s ¼” NPT quick connector is properly connected to the air hose.
- Ensure the airflow controller’s ¼” NPT quick connector is properly connected to the air hose.
- The airflow controller’s Deflate Valve is unlocked.
SPECIFICATIONS
- Model YD-127
- Working Voltage DC 12 V
- Power Rating 540 W
- Inflation Speed 160 L/Min
- Maximum Working Pressure 150 PSI
- Display Units PSI, Bar, kPa, kg/cm2
- Continuous Operating Time 45 Mins
- Air Hose Length 26.24 ft (8 m)
- Power Cord Length 6.56 ft (2 m)
- Dimensions 13.14 X 8.93 X 5.90 in/ 33.4 x 22.7 x 15 cm
RECYCLING
You may dispose of the product when its service life has ended, please -recycle the recyclable parts according to local guidelines.
WARRANTY PERIOD – AstroAI ASIKFCWR Wide Neck Plastic Foam Cannon
2-Year Limited Warranty from AstroAI. Each AstroAI Portable Air Compressor will be free from defects in material and workmanship. This warranty does not cover damage from neglect, misuse, contamination, alteration, accident, or abnormal conditions of operation or handling.
This warranty covers the original purchaser only and is not transferable. AstroAI always wants to provide our customers with excellent products and customer service.
Questions or concerns about AstroAI ASIKFCWR Wide Neck Plastic Foam Cannon? We’re happy to help! Please contact us via support@astroai.com
FAQs About AstroAI ASIKFCWR Wide Neck Plastic Foam Cannon
What is the required pressure for a foam cannon?
Suitable for the Majority of Pressure Washers: Most cold-water gas or electric pressure washers with a maximum PSI of 4000 are suitable with the foam cannon. At least 1600 PSI should be produced by the pressure washer in order to get the best foam.
What’s the wait time for a foam cannon?
I’m in South Florida, so depending on the heat and sun, give the foam five to ten minutes to sit before giving it a full rinse. Here, I’ll either carry out my usual two-bucket wash procedure again or I’ll just reapply any leftover foam, agitate it with a wash mitt, and then rinse. I’ve found the foam cannon to be quite useful.
Is any soap suitable for use in a foam cannon?
Avoid using ceramic soaps with SiO2 for foamers and/or combination wash and wax products. Both of these kinds of soaps don’t foam in a cannon as well as regular wash soap does.
Is water added to the foam cannon?
How to Fill Your Car with Foam. Fill the foam cannon’s canister with 1 to 3 ounces of your preferred Chemical Guys soap mixed with water. Warm water is what we always use because it improves the aerate combination. Reattach the canister to the foam cannon’s head.
Cannons made of foam be good or bad?
If you do own a pressure washer and don’t mind spending a little more time setting it up, the Foam Cannon will perform optimally and offer the best coverage while cleaning. Either a foam cannon or a foam gun is a good option because it’s better than having neither.
Why won’t my foam cannon work?
A partially obstructed nozzle, such as a tiny sand particle lodged in the nozzle aperture, could be the cause of this. Rinse the cannon in warm water to resolve this, and consider using a cleaning needle or similar tool. The user handbook has an included needle on the back.
For your foam cannon, do you use cold or hot water?
Using cutting-edge technology, your foam cannon creates the ideal blend of soap, water, and air to spew thick foam. To easily shoot thick suds, use warm water to help aerate the soap and water mixture.
Does a pressure washer have a foam cannon attached to it?
All Chemical Guys foam cannons are compatible with gas or electric pressure washers, which is how we at Detail Garage apply thick car washing foam.
Is a pressure washer necessary for a foam cannon?
A foam cannon is a piece of car wash equipment that uses the force of a pressure washer to spray thick suds all over your car when the ideal amounts of water, soap, and air are mixed.
How is a foam cannon assembled?
A foam cannon is a very simple piece of equipment used for washing cars. Simply unscrew the canister, fill it with soap and water, screw it back onto the brass connector, and mix the mixture by swirling it around rather than shaking it aggressively.
How much foam cannon dish soap is there?
Typically, I insert one inch of soap into the bottom of the bottle, add the remaining water, screw on the top, and give it a little shake. This has consistently produced enough dense foam for me to cover my car—two times, in fact.
For More Manuals by AstroAI, Visit Latest Manuals
- AstroAI Portable Air Compressor 100PSI User Manuals
- AstroAI YD-127 Heavy Duty Portable Air Compressor User Manual
- ASTROAI CF35 12 Volt Car Refrigerator User Manual
- AstroAI ASIACTODC-6A Electrical Power Converter User Manual
|
AstroAI ASIKFCWR Wide Neck Plastic Foam Cannon [pdf] User Manual |
