ADLER AD7425 Electric Blanket Underlay
IMPORTANT INSTRUCTIONS
PLEASE READ CAREFULLY. IMPORTANT INSTRUCTIONS, KEEP FOR LATER USE.
- Read the operating manual before using the device and follow the instructions contained in it. The manufacturer is not liable for damage caused by using the device against its intended use or improper handling.
- The device is for domestic use only. Do not use it for other purposes that are not by its intended use.
- Connect the device only to a 230 V ~ 50/60Hz. To increase the safety of use, do not switch on many electrical devices simultaneously to one circuit.
- Be extra cautious when using the device when children are nearby. Do not allow children to play with the device, do not let children or persons not familiar with the device use it. The equipment should not be used by young children, unless the controllers have been pre-set by parents or guardians, or children have been thoroughly instructed on how to safely handle the regulators.
Children under three years of age cannot use this device due to the lack of response to overheating. - WARNING: This equipment may be used by children over 8 years of age persons with limited physical, sensory, or mental abilities, or persons who have no experience or knowledge of the equipment, if this is done under the supervision of a person responsible for their safety or given to them. tips on the safe use of the device and are aware of the dangers associated with its use. Children should not play with the equipment. Cleaning and maintenance of the device should not be performed by children unless they are over 8 years of age and are supervised. This device cannot be used by people who are not heat sensitive, people who are very sensitive to heat, who are unable to respond to overheating, and people who require constant care.
- Always after use, remove the plug from the socket by holding the socket with your hand. DO NOT pull on the power cord.
- Do not immerse the cable, plug, and the entire device in water or other liquid. Do not expose the device to atmospheric conditions (rain, sun, etc.), or do not use it in conditions of high humidity (bathrooms, damp camping houses).
- Periodically check the condition of the power cord. If the power cord is damaged, it should be replaced by a specialist repair facility to avoid a hazard.
- Do not use the device with a damaged power cord or the device is not working properly.
Do not repair the device yourself, as it may cause shock. Please return the defective device to the appropriate service center for inspection or repair. All repairs may only be carried out by authorized service points. Incorrectly performed repairs can cause danger to the user. - Do not use the device near flammable materials.
- Do not leave the device or the adapter connected to the outlet unattended.
- To provide additional protection, it is advisable to install a residual current device (RCD) with a rated residual current not exceeding 30 mA in the electrical circuit. In this regard, please contact an electrician.
- Do not allow the device or adapter to get wet. If the device falls into the water, immediately pull the plug or adapter from the power socket. Do not put your hands into water when the device is connected to the mains. Before re-use, it must be checked by a qualified electrician.
- Do not handle the device or adapter with wet hands.
- The device should be turned off every time you put it down.
- Do not use the device near water, for example: in the shower, in the bathtub, or above the basin with water.
- If the device uses a power supply, do not cover it, as it could lead to a dangerous increase in temperature and damage to the device. Always, first insert the plug into the power socket in the device and then the power supply to the mains socket.
- Do not use the bed sheet in folded condition. Do not put pins, needles, and other metal objects in the sheet.
- Do not use the sheet if it is wet. Leave the sheet hung loosely in a ventilated area until it is completely dry.
- Do not put the power cord on a warmed sheet. Do not fold the equipment when it is placed on top during storage. Check the equipment periodically for signs of wear or damage.
If such signs or equipment are used improperly, please contact your supplier before continuing to use it. - Store in a dry place. Never put heavy objects on the sheet.
- Never go to sleep with the electric sheet turned on. Unplug the power plug from the outlet.
- Never cover the controller.
- Before switching on the electric sheet, make sure that it is evenly distributed, there are no kinks or folds.
- The product can be washed in the washing machine at 30°C temperature. Can be washed by hand. Disconnect the power cord and controller before washing. Switch or controller – the regulator must not be wet during washing, and during drying the cord must be in a horizontal position to ensure that the water does not flow into the switch or controller – the regulator.
- Do not iron the electric sheet!
- This equipment is not intended for medical use in hospitals.
- The device should cool down before storage.
- The device may be used only with the types of removable elements specified in the equipment marking.
- Do not use the device on adjustable beds or if the device is used on an adjustable bed, check that the blanket and cord cannot get stuck or corrugated, eg on hinges.
- The device is equipped with a fuse protecting against overheating, which should not work when used by the intended use of the equipment. If the fuse trips, the device will stop working, and the equipment must be returned to the manufacturer or its representative for repair.
Product: Electric blanket underlay AD7425 / AD7426
SAFETY SYMBOLS
- Read the Instructions.
- Do not use folded or corrugated.
- Do not knock out pins, needles, or other objects.
- Do not use for very small children (0-3 years).
- Maximum washing temperature 30 ° C. Normal process.
BEFORE FIRST USE
- The product needs to be unfolded and laid flat before switching on.
- Fix the product according to the instructions in the chapter: Fitting your product on the bed.
- We recommend that you switch your product to the maximum setting for two to three hours before bedtime then reduce to your desired heat setting 15 minutes before getting into bed. You must switch OFF before sleeping.
Fitting your product on the bed
- Place the product onto the mattress with the controller (or two) at the HEAD END but towards the foot end of the bed.
- The control switches should be below the normal head’s sleeping position.
- Unroll the tie tapes and pass the tapes under the bed as shown in the diagrams (Fig.1-6).
- Ensure the heating wires do not extend under pillows or hang over the sides. Pass the middle tie tape under the mattress and through the middle loop on the opposite side (Fig.1). Pass the end of the tape under the corresponding bottom corner of the mattress (Fig. 2) up through the center loop of the product (Fig. 3) and down under opposite corner of the mattress and then through side loop on the opposite side of the product (Fig 4).
- Repeat this process at the other end (Fig. 5).
DESCRIPTION OF THE DEVICE
mechanical controller
- Temperature controller
- Power cord
- Bed sheet/blanket/mat
- Socket to disconnect the power cord before washing
OPERATING INSTRUCTIONS
manual controller
- 1. Plug the power cord into an electrical outlet.
- 2. Active the product by moving the switch to position 1/2/3.
- 0 – switching off
- 1 – low, gentle heat, LED on
- 2 – medium heat, diode on
- 3 – high heat, diode on
- 3. Switch off the device that moves the switch to position 0.
STORING
Always allow the product to cool down before folding and storing. Your product can remain on the bed all year round as a comfortable under-blanket. Simply remove the controls and store them until Winter. If you wish to remove the product from your bed when not in use, roll or fold it loosely and store it in a bag. Avoid creating sharp creases in the product; for example, do not store it under other items that may result in bending the inside heating wires.
CLEANING & AIR DRYING
The product can be machine-washed because it is equipped with detachable controllers. Unplug and remove one or two power cords with controllers from socket (4) to disconnect the power cord before washing. Fold and presoak the product for 15 minutes in a mild soap and lukewarm water solution. Ensure the water temperature is less than 30°C.
- Wash on the delicate or gentle cycle for 2 minutes.
- Rinse in fresh lukewarm water.
- Gently stretch the product to its original size.
- Air dry over a clothesline. DO NOT use clothes pegs or clips of any kind.
- DO NOT use the product until it is completely dry!
- DO NOT iron the product!
TECHNICAL DATA
AD7425 / AD7426
- Nominated power input: 60W / 2 x 60W
- Supply voltage: 230 V ~ 50/60Hz
- Dimensions (high x width) cm: 150X80 / 150X160
DISPOSAL
To protect your environment: please separate carton boxes and plastic bags and dispose of them in corresponding waste bins.
Used appliances should be delivered to the dedicated collecting points due to hazardous components, which may affect the environment. Do not dispose of this appliance in the common waste bin.
For More Manuals by ADLER, Visit LatestManuals
